NEW E-SERIES
Since the release of the Ozroll Drive System in 2006 we have continued to work on ways to improve this revolutionary product. In response to recent battery technology advancements, the NEW E-SERIES was developed.
The new controls are more compact and stylish than the current ODS Control and are available in two concepts - The E-Port and The E-Fix.
|
The E-Port Concept E-Port is a portable controller designed to be shared using the wall plate concept The newer technology of the Li-Ion battery has allowed us to drastically reduce the size of the portable controller resulting in the creation of E-Port. The E-Port has a large battery capacity (1,400mAh) The E-Port controller while being 30% smaller than the current Control 10 it still has a similar power capacity. E-Port is also available with a RF option |
 |
Features and Benefits
The E-Port controller is removable and can be used to operate more than
one roller shutter further highlighting the overall cost effectiveness of
the system.
The E-Port controller is required to work in conjunction with The E-Port Wall Plate allowing for the power to be generated from the battery through to the motor.
"Re-chargeable Li-Ion batteries.
" In Built electronic circuit board
" Intelligent LED indicators
" Safe and Simple charging
" Suits both the T2 and L10 battery motors
Available in Standard and RF controls.
E-Fix DC Control Concept
E-Fix is designed to be used one per shutter and is the non-portable option with the battery pack concealed in the wall cavity.
The E-Fix has 3 different options for battery recharging The standard E-Series Charger,The In-wall Charger, and The New E-Solar Charger
E-Fix control is available with RF.
E-Fix DC Control
E- Fix DC is made up of two parts - The Controller and the In Wall Battery.
The
battery is fitted inside the wall cavity and the controller simply presses
onto the battery section. This allows for the Battery to be changed separately
to the Controller allowing for simple service and upgrade ability.
Another unique feature is the "Favourite" position that will allow the user to program a preferred shutter position.
*Installation on Plasterboard walls will require the use of a C-Clip Bracket which is available as the E-Flush Mount Kit
E-Series Charger, In-Wall Charger
The in Wall Charger is a variation of the current charger system and has been slightly modified so it can be permanently wired to the wall plate to maintain a constant charge. The charger pack can be fitted into ceiling or roof cavity, an electrician is required to install a standard 240 volt power outlet. This product is recommended to be used with the RF installation as it draw more power with the RF always on
E-Solar
E-Solar is a convenient and cost effective stand alone system that uses renewable energy from the sun.
The E-Solar is designed to be used in conjunction with our E-Fix control allowing for a quick and simple installation where the battery is stored inside the home and protected from the elements.
The Solar panel can be mounted on the roof, the building or even on the shutter box.
The E-Port and E-Fix RF
As the RF controller is constantly monitoring the RF remote for a transmitted signal it will consume battery power at a higher rate than the standard controller
With this in mind it is recommended that the RF controller is used in conjunction with the In Line Charger.
The charger pack can be fitted into ceiling or roof cavity, an electrician is required to install a standard 240 volt power outlet
E-Trans
RF Remote
The E-Trans RF Remote will provide wireless control of the E-Port and E-Fix RF systems and is offered in two versions 1 Channel and 9 Channel
Both versions will only operate a shutter that is using the RF controller. The RF remote will not operate a standard controller
The RF Remote when programmed can operate one or more rollershutters connected to the RF controller. The 1 Channel version will allow for only one combination to be programmed. The 9 Channel version will allow for up to 9 different combinations. These combinations are totally programmable by the user.
Prior to use you must pull out the yellow tag, from the inside of the remote, this will then activate the battery. The RF Remote will not operate until this is done.
For further information regarding the programming of the remote, please refer to the instructions provided with each unit. Each unit has it's own wall plate
The RF REmote is powered by a long life battery, which dose not require recharging.
The life of the battery will be approximately 2 years depending on usage
Components Price List
Upgrade the standard E-Port portable controller to E-Port RF portable controller cost $30.00
Upgrade the standard E-Fix fixed position controller to E-Fix RF fixed position controller cost $25.00
The E-Trans RF Remote for the E-Port and E-Fix RF systems
1 Channel E- Trans RF remote $59.00
9 Channel E- Trans RF remote $72.00
E-Series In-Wall Charger $10.00
E-Solar 2w solar charging panel $52.00
All Prices include GST
When you place your order at Order On Line immediately send an email to us for the up grade parts you require.